banner



How To Remove Asus Vg248qe Monitor Stand

Introduction

Need to access the internals of your ASUS VG248? Here'southward a guide that shows how to remove the frame and open the display.

  1. Before you begin, lay the monitor face down on a smooth, clean surface. Four rubbery covers hide four screws in the rear of the monitor.

    • Earlier you begin, lay the monitor face down on a smoothen, clean surface.

    • Four rubbery covers hide 4 screws in the rear of the monitor.

    • Pry out the plastic covers with a stiff pointed tool, like a metal spudger.

  2. Remove the four 13.4 mm Philips #1 screws securing the monitor stand.

    • Remove the four thirteen.4 mm Philips #1 screws securing the monitor stand.

  3. Remove the stand from the display. Remove the stand from the display.

    • Remove the stand from the display.

  4. The display bezel is held to the rear case by plastic clips that can be released by pulling straight up on the bezel. Rather than use any prying tools that could damage the LCD, it's best to just pull with your fingers. A thin cloth will both protect your fingertips and prevent you from smudging the LCD.

    • The display bezel is held to the rear example by plastic clips that can be released past pulling straight up on the bezel.

    • Rather than use any prying tools that could damage the LCD, it'southward best to just pull with your fingers. A thin cloth will both protect your fingertips and prevent you from smudging the LCD.

    • Lay the cloth over one of the long edges of the brandish.

    • Grip the side of the bezel through the textile and lift straight upwards. A few clips in the centre will popular gratuitous.

    • Be conscientious to pull directly upwards, and non pry against the display. Pushing down on the display could impairment it.

  5. Repeat the procedure around the display, lifting up the center of the next side. Repeat the procedure around the display, lifting up the center of the next side.

    • Echo the procedure around the display, lifting upwards the center of the next side.

  6. Move around to the other long side and lift up on the center of the bezel. Move around to the other long side and lift up on the center of the bezel.

    • Move around to the other long side and lift upwardly on the center of the bezel.

  7. Grip the center of the final side and lift the bezel away from the rear case. Grip the center of the final side and lift the bezel away from the rear case.

    • Grip the center of the terminal side and elevator the bezel away from the rear case.

  8. Now that you've freed the centers of the four sides, it's time to move on to the corners. Each corner is secured by two large clips that can't be freed by just pulling straight up like you did with the sides.

    • Now that you've freed the centers of the four sides, it's fourth dimension to move on to the corners.

    • Each corner is secured by two large clips that can't be freed by only pulling straight up like you did with the sides.

    • In the next step, you'll be pushing in on the corner clip on the left of the bottom edge of the bezel.

    • Using a thin stiff prying device, like a Jimmy, press in against the bottom prune in the lower left corner (beneath the HDMI logo).

    • While pressing the clip in, pull upward on the lower edge of the bezel. The unabridged corner should pop gratis.

  9. Once you've freed one corner, you should be able to gently twist the bezel off, freeing all of the remaining corners. If any corners are particularly stubborn, repeat the previous step on the difficult corner. If any corners are particularly stubborn, repeat the previous step on the difficult corner.

    • In one case you've freed 1 corner, yous should be able to gently twist the bezel off, freeing all of the remaining corners.

    • If any corners are particularly stubborn, repeat the previous pace on the difficult corner.

  10. Remove the bezel.

    • Remove the bezel.

  11. Lift the LCD out of the rear case. The row of adjustment buttons will come out of the case with the display, attached by a thin ribbon cable. Take care not to damage the cable.

    • Lift the LCD out of the rear case.

    • The row of adjustment buttons will come up out of the case with the display, attached past a thin ribbon cable. Take care not to damage the cablevision.

  12. With the casing removed, you now have access to the button board, cables, and the housing over the motherboard components.

    • With the casing removed, yous now have access to the button board, cables, and the housing over the motherboard components.

Conclusion

To reassemble your device, follow these instructions in reverse guild.

Squad

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview

How To Remove Asus Vg248qe Monitor Stand,

Source: https://www.ifixit.com/Guide/ASUS+VG248+Disassembly/71911

Posted by: colepliteard.blogspot.com

0 Response to "How To Remove Asus Vg248qe Monitor Stand"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel